Main Features
Compact Design
The Hydroid EZ features a compact design that allows it to fit easily under most kitchen and wet-bar sinks, maximizing space utilization in your home.
User-Friendly Operation
Designed with user convenience in mind, the Hydroid EZ features intuitive controls and indicators for easy operation and maintenance.
Enhanced Durability
Constructed with high-quality materials and built to withstand the rigors of daily use, the Hydroid EZ is engineered for long-lasting durability and reliability.
Warranty Coverage
At Water Service Company, trust is our priority. We promise top-notch water treatment solutions that stand the test of time. Rest easy knowing your investment is protected with our comprehensive warranties:
Hydroid EZ
Backed by a 1-year limited warranty from the purchase date.
Got questions? We're here for you! Contact our customer service team for any warranty inquiries. Your satisfaction is our commitment.
Components
Hydroid EZ
Filters
Tank
Faucet
WARNING: Connect your system to the cold water supply only. Do not use a water supply that is micro-biologically unsafe, or of unknown source without adequate disinfection before or after the hydroid EZ™ RO system.
Tubing | Directions |
1/4” Green | Feed water supply line to inlet. Feed ball valve labeled “TO FEED” |
1/4” Blue | Carbon post filter elbow labeled “TO FAUCET” to center threaded shank of faucet |
1/4” Yellow | Carbon post filter tee labeled “TO TANK” to ball valve on storage tank |
1/4” Red | Flow restrictor labeled “TO DRAIN” to DS-EZW4 drain clamp. |
WARNING: Connect your system to the cold water supply only. Do not use a water supply that is micro-biologically unsafe, or of unknown source without adequate disinfection before or after the system.
Tubing | Directions |
1/4” Green | Feed water supply line to inlet. Feed ball valve labeled “TO FEED” |
1/4” Blue | Carbon post filter elbow labeled “TO FAUCET” to center threaded shank of faucet |
1/4” Yellow | Carbon post filter tee labeled “TO TANK” to ball valve on storage tank |
1/4” Red | Flow restrictor labeled “TO DRAIN” to air gap 1/4” drain/barb inlet at faucet air gap |
3/8” Red | 3/8” Barb on air gap to DS-EZW6 Drain clamp |
Troubles | Cause | Solution |
---|---|---|
Unit fails to produce water | Water supply is turned off.Not enough water pressure to system.Prefilters clogged.Flush valve on unit is in the open position. |
|
Milky colored water | Air in system | Air in system is a normal occurrence With initial startup of the ro system. This milky look disappears during Normal use within1 to 2 weeks. |
Noise from faucet | Air gap faucet.Location of drain saddle.Restriction in drain line. | Normal with air gap faucet.Relocate the drain to horizontal.Blockage sometimes caused by debris from garbage disposal or dishwasher. |
Unit produces water but only getting a small amount out of tank. | Tank ball valve is in the closed position.Prefilters are clogged.Membrane is fouled.No air pressure in tank.Check valve on product side not holding. |
Open the tank ball valve.Change prefilters.
|
Slow production. | Low water pressure.Crimps in tubing.Clogged pre-filters.Fouled membrane. | Make sure pump is working.Make sure tubing is straight.Replace pre-filters.Replace membrane. |
Water taste or smell offensive | Post carbon is depleted.Fouled membrane.Sanitizer not flushed out. | Replace post carbon.Replace membrane.Drain storage tank and refill overnight. |
No drain water | Clogged flow restrictor. | Replace flow restrictor. |
Unit producing water too rapidly. | Tubing connected incorrectly.Membrane failure. |
Make sure drain and product lines are connected properly.
|
Water runs to drain all the time | Auto shutoff not closing.Check valve on product side not holding.No air pressure in tank. | Replace auto shutoff.Replace check valve.Increase air pressure in tank while empty to 6 psi -7 psi. |
Leaks | Fittings are not tightened.Missing o-rings.Misalignment of hole in drain saddle. | Tighten fittings as necessary.Contact local dealer.Realign drain saddle. |